Filters
All
Adhesives/Sealants - Medtech22Additives71Coatings/Dispersions - Medtech27Elastomer Gels1Encapsulation Technology1Fluids - Medtech7Foams - Medtech2Gels - Medtech5Inks - Medtech6High Consistency Rubbers - Medtech48Low Viscosity Elastomers - Medtech23Liquid Silicone Rubbers - Medtech37Primers - Medtech9Pressure Sensitive Adhesives - Medtech3Soft Silicone Adhesives5Specialty Fluids1Greases - Medtech4
Refine results
Product
Product Type
Description
Fluids - Medtech
A clear liquid trifluoroprophylmethylsiloxane to provide lubricious and/or hydrophobic coating, for lubricating the surfaces of molded dimethyl silicone elastomer parts
Available in standard viscosities of : 350 cP, 1,000 cP, and 12,500 cP.
Custom viscosities available upon request
Available in standard viscosities of : 350 cP, 1,000 cP, and 12,500 cP.
Custom viscosities available upon request
Liquid Silicone Rubbers - Medtech
Two-part, translucent silicone system designed for use with injection molding equipment
Rapid cure with no post-cure required
1:1 Mix Ratio (Part A: Part B)
Rapid cure with no post-cure required
1:1 Mix Ratio (Part A: Part B)
High Consistency Rubbers - Medtech
Uncatalyzed, vinyl-functional, high consistency silicone elastomer
Requires addition of a peroxide catalyst for vulcanization
Strained through a 400-mesh screen (minimum) to ensure freedom from particulate contamination
Requires addition of a peroxide catalyst for vulcanization
Strained through a 400-mesh screen (minimum) to ensure freedom from particulate contamination
Primers - Medtech
Specially formulated primer
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with condensation cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with condensation cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
Inks - Medtech
Strong adhesion to other silicones
Dispersed in Xylene
Accelerated cure with introduction of heat
Cures via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Dispersed in Xylene
Accelerated cure with introduction of heat
Cures via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Foams - Medtech
Two-part, room temperature curing, silicone foam
Platinum cure
Yields a low density silicone foam when catalyzed
1:1 Mix Ratio (Part A: Part B)
Platinum cure
Yields a low density silicone foam when catalyzed
1:1 Mix Ratio (Part A: Part B)
Liquid Silicone Rubbers - Medtech
Two-part, translucent silicone system used with injection molding equipment
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Additives
An orange, single component masterbatch, with the consistency of a low viscosity paste
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Additives
A orange, single component masterbatch, with the consistency of a low viscosity paste
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Supported by USP Class VI and ISO 10993 Biological testing (reference Biological Testing Data Table)
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Supported by USP Class VI and ISO 10993 Biological testing (reference Biological Testing Data Table)
Low Viscosity Elastomers - Medtech
Pourable, optically clear, two-part silicone elastomer
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)