Filters
Applied Filters
General Healthcare
Adhesives/Sealants - Medtech8Additives37Coatings/Dispersions - Medtech15Fluids - Medtech4Foams - Medtech1Inks - Medtech6High Consistency Rubbers - Medtech31Low Viscosity Elastomers - Medtech12Liquid Silicone Rubbers - Medtech17Primers - Medtech9Pressure Sensitive Adhesives - Medtech3Soft Silicone Adhesives5Greases - Medtech4
Refine results
Product
Product Type
Description
High Consistency Rubbers - Medtech
Uncatalyzed, vinyl-functional, high consistency silicone elastomer
Requires addition of a peroxide catalyst for vulcanization
Strained through a 400-mesh screen (minimum) to ensure freedom from particulate contamination
Requires addition of a peroxide catalyst for vulcanization
Strained through a 400-mesh screen (minimum) to ensure freedom from particulate contamination
Primers - Medtech
Specially formulated primer
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with condensation cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with condensation cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
Inks - Medtech
Strong adhesion to other silicones
Dispersed in Xylene
Accelerated cure with introduction of heat
Cures via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Dispersed in Xylene
Accelerated cure with introduction of heat
Cures via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Foams - Medtech
Two-part, room temperature curing, silicone foam
Platinum cure
Yields a low density silicone foam when catalyzed
1:1 Mix Ratio (Part A: Part B)
Platinum cure
Yields a low density silicone foam when catalyzed
1:1 Mix Ratio (Part A: Part B)
Liquid Silicone Rubbers - Medtech
Two-part, translucent silicone system used with injection molding equipment
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Primers - Medtech
Specially formulated primer
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with one and two-part RTV systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with one and two-part RTV systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
Liquid Silicone Rubbers - Medtech
Two-part, translucent silicone system designed for use with injection molding equipment
Self-lubricating
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Self-lubricating
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Liquid Silicone Rubbers - Medtech
Two-part, translucent silicone system used with injection molding equipment
Rapid cure with no post-cure required
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Rapid cure with no post-cure required
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Inks - Medtech
One-part, flowable silicone elastomer dispersion
Cures at room temperature upon exposure to atmospheric moisture
Non-corrosive cure system
Cures at room temperature upon exposure to atmospheric moisture
Non-corrosive cure system
Low Viscosity Elastomers - Medtech
Flowable, two-part, optically clear, high durometer silicone
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)