Filters
Applied Filters
General Healthcare
Adhesives/Sealants - Medtech8Additives37Coatings/Dispersions - Medtech15Fluids - Medtech4Foams - Medtech1Inks - Medtech6High Consistency Rubbers - Medtech31Low Viscosity Elastomers - Medtech12Liquid Silicone Rubbers - Medtech17Primers - Medtech9Pressure Sensitive Adhesives - Medtech3Soft Silicone Adhesives5Greases - Medtech4
Refine results
Product
Product Type
Description
Additives
A orange, single component masterbatch, with the consistency of a low viscosity paste
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Supported by USP Class VI and ISO 10993 Biological testing (reference Biological Testing Data Table)
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Supported by USP Class VI and ISO 10993 Biological testing (reference Biological Testing Data Table)
High Consistency Rubbers - Medtech
High tensile strength, low modulus high consistency silicone rubber
Low tensile set and low hysteresis qualities
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Low tensile set and low hysteresis qualities
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
High Consistency Rubbers - Medtech
Uncatalyzed, vinyl-functional, high consistency silicone elastomer
Requires addition of a peroxide catalyst for vulcanization
Strained through a 400-mesh screen (minimum) to ensure freedom from particulate contamination
Requires addition of a peroxide catalyst for vulcanization
Strained through a 400-mesh screen (minimum) to ensure freedom from particulate contamination
Primers - Medtech
Specially formulated primer
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with condensation cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with condensation cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
Inks - Medtech
Strong adhesion to other silicones
Dispersed in Xylene
Accelerated cure with introduction of heat
Cures via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Dispersed in Xylene
Accelerated cure with introduction of heat
Cures via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Foams - Medtech
Two-part, room temperature curing, silicone foam
Platinum cure
Yields a low density silicone foam when catalyzed
1:1 Mix Ratio (Part A: Part B)
Platinum cure
Yields a low density silicone foam when catalyzed
1:1 Mix Ratio (Part A: Part B)
Liquid Silicone Rubbers - Medtech
Two-part, translucent silicone system used with injection molding equipment
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Primers - Medtech
Specially formulated primer
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with one and two-part RTV systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with one and two-part RTV systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
High Consistency Rubbers - Medtech
A unique three-part system, VersaSil3 offers the flexibility of adjustable cure rate and table life for various fabrication requirements
High tear strength, wide processing parameters, and translucent, non-tacky surfaces
Developed to be compounded with the inhibitor CAT-40 and the platinum catalyst CAT-55. Advantages include: no volatile by-products, lower cure temperature, and optional post-cure
100: 1.0: 1.0 Mix Ratio
High tear strength, wide processing parameters, and translucent, non-tacky surfaces
Developed to be compounded with the inhibitor CAT-40 and the platinum catalyst CAT-55. Advantages include: no volatile by-products, lower cure temperature, and optional post-cure
100: 1.0: 1.0 Mix Ratio
Additives
A black, single component masterbatch, with the consistency of a clay like material
Product exhibits enhanced resistance to color change as a result of prolonged exposure to heat when compared to MED-4102-2
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Supported by USP Class VI and ISO 10993 Biological testing (reference Biological Testing Data Table)
Product exhibits enhanced resistance to color change as a result of prolonged exposure to heat when compared to MED-4102-2
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Supported by USP Class VI and ISO 10993 Biological testing (reference Biological Testing Data Table)