Filters
Applied Filters
Medical Implants
Refine results
Product
Product Type
Description
Low Viscosity Elastomers - Medtech
A two-part, translucent pourable silicone elastomer
Cures with heat via addition-cure chemistry
10:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
10:1 Mix Ratio (Part A: Part B)
Low Viscosity Elastomers - Medtech
Two-part, optically clear, solvent free, low viscosity silicone elastomer
Cures with heat via addition-cure chemistry
10:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
10:1 Mix Ratio (Part A: Part B)
Liquid Silicone Rubbers - Medtech
Two-part, white silicone system designed for use with injection molding equipment
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
High tear strength
Designed to resist blocking and rehealing that otherwise might be induced by the radiation sterilization of molded parts.
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
High tear strength
Designed to resist blocking and rehealing that otherwise might be induced by the radiation sterilization of molded parts.
Liquid Silicone Rubbers - Medtech
Two-part, translucent silicone system designed for use with injection molding equipment
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Liquid Silicone Rubbers - Medtech
Two-part, translucent silicone system designed for use with injection molding equipment
Rapid cure with no post-cure required
1:1 Mix Ratio (Part A: Part B)
Rapid cure with no post-cure required
1:1 Mix Ratio (Part A: Part B)
High Consistency Rubbers - Medtech
Two-part, high consistency silicone elastomer
Cures with heat via addition-cure chemistry
Has a non-tacky surface and no volatile by-products or peroxide residues
Strained through a 400-mesh screen (minimum)
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
Has a non-tacky surface and no volatile by-products or peroxide residues
Strained through a 400-mesh screen (minimum)
1:1 Mix Ratio (Part A: Part B)
High Consistency Rubbers - Medtech
Two-part, low tension set silicone elastomer
Cures with heat via addition-cure chemistry
Has a non-tacky surface and no volatile by-products or peroxide residues
Strained through a 400-mesh screen (minimum)
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
Has a non-tacky surface and no volatile by-products or peroxide residues
Strained through a 400-mesh screen (minimum)
1:1 Mix Ratio (Part A: Part B)
Primers - Medtech
Specialty formulated primer
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with platinum-cured systems on polycarbonates
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with platinum-cured systems on polycarbonates
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
Coatings/Dispersions - Medtech
Cures with heat via addition-cure chemistry
Intended to be dispersed in solvent at a suggested mix ratio of 100parts Part A: 1part Part B: 1part Part C: 234parts Xylene (or other suitable solvent)
Intended to be dispersed in solvent at a suggested mix ratio of 100parts Part A: 1part Part B: 1part Part C: 234parts Xylene (or other suitable solvent)
High Consistency Rubbers - Medtech
Two-part, high tear strength silicone elastomer
Cures with heat via addition-cure chemistry
Has a non-tacky surface and no volatile by-products or peroxide residues
Strained through a 400-mesh screen (minimum)
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
Has a non-tacky surface and no volatile by-products or peroxide residues
Strained through a 400-mesh screen (minimum)
1:1 Mix Ratio (Part A: Part B)