Filters
Applied Filters
Medical Implants
Refine results
Product
Product Type
Description
Inks - Medtech
Strong adhesion to other silicones
Dispersed in Xylene
Accelerated cure with introduction of heat
Cures via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Dispersed in Xylene
Accelerated cure with introduction of heat
Cures via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
High Consistency Rubbers - Medtech
Two-part, high tear strength silicone elastomer
Cures with heat via addition-cure chemistry
Has a non-tacky surface and no volatile by-products or peroxide residues
Strained through a 400-mesh screen (minimum)
1:1 Mix Ratio (Part A: Part B)
Cures with heat via addition-cure chemistry
Has a non-tacky surface and no volatile by-products or peroxide residues
Strained through a 400-mesh screen (minimum)
1:1 Mix Ratio (Part A: Part B)
Additives
A yellow, single component masterbatch, with the consistency of a low viscosity paste
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Additives
A black, single component masterbatch, with the consistency of a low viscosity paste
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Additives
A green, single component masterbatch, with the consistency of a low viscosity paste
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Consists of pigment dispersed in a vinyl-functional silicone polymer which covalently bonds into the matrix of platinum-cured silicone systems
Primers - Medtech
Specially formulated primer
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with platinum-cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with platinum-cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
Primers - Medtech
Specially formulated primer
One component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with platinum-cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with platinum-cured systems where conventional silicone primers are insufficient
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
High Consistency Rubbers - Medtech
High tensile strength, low modulus high consistency silicone rubber
Low tensile set and low hysteresis qualities
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Low tensile set and low hysteresis qualities
Cures with heat via addition-cure chemistry
1:1 Mix Ratio (Part A: Part B)
Primers - Medtech
Specialty formulated primer
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with platinum-cured systems on polycarbonates
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
One-component primer supplied in VM&P Naphtha requires no mixing
Easy to use, air-drying, one-part primer designed for use with platinum-cured systems on polycarbonates
Flash Point (TCC) of 17°C (63°F)
Convenient container sizes yield less waste
Coatings/Dispersions - Medtech
Cures with heat via addition-cure chemistry
Intended to be dispersed in solvent at a suggested mix ratio of 100parts Part A: 1part Part B: 1part Part C: 234parts Xylene (or other suitable solvent)
Intended to be dispersed in solvent at a suggested mix ratio of 100parts Part A: 1part Part B: 1part Part C: 234parts Xylene (or other suitable solvent)